Thickness Gauge

Product Details:

Elcometer 500 Concrete Coating Thickness Gauge accurately measures the thickness of coatings on concrete and other similar substrates (eg plasterboard, drywall, concrete block, brick) – non destructively.

 

Features

• Fast and accurate, the Elcometer 500 Coating Thickness Gauge takes repeatable and reproducible dry film thickness measurements of coatings on concrete up to 10mm‡ thick (Epoxy coatings, thickness on other materials may vary) or other similar substrates – without damaging the coating.
• Easy to read, user definable display with automatic screen brightness
• Store up to 100,000 readings in up to 1,000 alpha-numeric batches
• Rugged, intelligent ergonomic probes, designed for continuous use and field replaceable probe tips you can inspect all day, everyday
• Measure up to 10mm
  • C1 150 – 2,500μm & C2 750 – 10,000μm
• Measure more than 60 readings per minute in standard mode and over 140 readings per minute in scan mode – allows users to inspect more coatings in less time.
• Rugged, dust & waterproof design equivalent to IP54, ideal for almost all environments
• The built in signal strength indicator on the Elcometer 500 Coatings on Concrete Gauge prevents false or incorrect readings, as the gauge only displays the coating thickness measurement if the signal strength indicator goes green.
• Incredibly easy to use, can be used in accordance with ASTM D6132, SSPC PA9 & ISO 2808 Method 10
• USB & Bluetooth® data output to PC and Android™ or iOS mobile devices
• Compatible with ElcoMaster® software and ElcoMaster® Mobile App, individual coating thickness measurements can be transferred via USB or Bluetooth® to PC or a mobile device for analysis and instant report generation.

Additional Information:

• Packaging Details: Elcometer 500 Coating Thickness Gauge Model B & T Elcometer 500 Coating Thickness Gauge, 4ml (0.14fl oz) Bottle of Probe Tip Oil, 120ml (4fl oz) Bottle of Ultrasonic Couplant, 2 x AA Batteries, Protective Case, Transit Case (Model T), Wrist Harness, 3 x Screen Protector, ElcoMaster¿¿ Software (Model T), USB Cable (Model T), Test Certificate Elcometer 500 Coatings on Concrete Inspection Kit Elcometer 500 Model T Coating Thickness Gauge, C1 & C2 coating thickness probes, C1 & C2 probe measurement foils: 1, 2, 3 & 8mm (40, 80, 120 & 310mils), Elcometer 456 Model B Ferrous Integral Gauge, Elcometer 456 calibration foils: 0.5 & 1.5mm (20 & 60mils), 2 x coating calibration moulds, 2 x Wrist Harness, 6 x Screen Protector, 120ml (4fl oz) bottle of ultrasonic couplant, 4ml (0.14fl oz) bottle of probe tip oil, transit case, ElcoMaster¿¿ software & USB cable

Product Details:

Wet film wheels are high precision, accurate and easy to use instruments consisting of a set of three wheels, with measurement ranges from 0-25μm to 0-3000μm.

Using a wet film wheel: roll the wheel through a wet coating, the centre wheel eventually touches the film. This point on the scale indicates the thickness. When the volume to solids ratio of the coating is known, generally found on a product data sheet, the wet film thickness can be used to predict the dry film thickness. Roll from maximum to minimum to avoid a false reading caused by surface tension.

WET FILM WHEELS 

The Elcometer 3230 wet film wheel consists of a central eccentric wheel and two outer concentric wheels. The diameter of the outer wheels is greater than that of the central wheel. By rolling the gauge through a wet coating, the centre wheel eventually touches the film. This point on the scale indicates the thickness. Various wet film thickness ranges are available up to a maximum of 1000pm (40mils). 

Elcometer 3230 Coil Coating Wet Film Wheels
Elcometer 3230 but the outer wheels are knurled to allow measurements to be taken on slippery coatings or on fast-moving substrates. Two separate wet film thickness ranges are available; 0 - 50pm (0 - 2mils) and 0 - 100pm (0 - 4mils). 

Product Details:

We are engaged in providing the broad assortment of Dry Film Coating Thickness (DFT) gauge used to measure the thickness of dry film coating, this gauge is well known in worldwide. Dry film thickness gauge is available in three different models. Each coating thickness gauge provides the user with increasing functionality. Integral coating thickness gauges are ideal for single handed operation as the wide footprint of the internal probe provides greater stability during coating thickness measurement - allowing for consistent, repeatable and accurate dry film thickness results. Separate coating thickness gauge models, with their wide range of probes, provide even greater dry film thickness measurement flexibility. Compatible with desktop and mobile software, individual coating thickness measurements can be transferred via USB or Bluetooth^® to PC or a mobile device for analysis and instant report generation.

Efficient:

• Fast reading rate of 70+ per minute, 140+ per minute with Ultra/Scan Probe
• Multiple calibration memories
• Alpha numeric batch identification
• User selectable calibration methods
• Compatible with ElcoMaster^® and ElcoMaster^® Mobile App

Powerful:

• Wide range of interchangeable probes
• USB and Bluetooth^® data output to iPhone* or Android™ devices
• Stores up to 150,000 readings in 2,500 batches
• Measures up to 31mm (1220mils) of coating on metal substrates

The importance of Coating Thickness Gauge Calibration:

• Formal quality systems, such as those described in ISO 9001, require coating thickness gauges to be properly controlled, logged and calibrated. Increasingly, users are specifying that the readings taken by thickness gauges are traceable to National Standards.

Product Details:

Featuring a highly durable ‘snap on’ replaceable probe cap, the Coating Thickness Gauge Ultra/Scan Probe is a revolutionary design which allows users to take individual dry film thickness readings or rapidly scan large surface areas - without damaging the probe or the coating.

 

When used in conjunction with the Coating Thickness Gauge Scan or Auto Repeat Modes, the Ultra/Scan Probe enables users to significantly reduce dry film thickness inspection times without affecting accuracy.

 

The Ultra/Scan Probe uses the Coating Thickness Gauge’s ensuring that any cap wear during use is incorporated within the calibration process. The coating thickness gauge even informs the user when to replace the cap.

• Scan Mode

 

When the Scan Mode is selected from the coating thickness gauge, users can slide the Ultra/Scan probe over the entire surface area. As the probe is lifted off the surface the gauge displays the average coating thickness value, the highest thickness and the lowest dry film thickness values. Each set of three dry film readings (average, high and low) can be displayed on the run graph and stored into the coating thickness gauge's memory.

 

During each scan, the coating thickness gauge displays the live thickness reading together with an analogue bar graph which graphically indicates the thickness relative to both the nominal thickness and any user-defined limits.

• Auto Repeat Mode

When the Ultra/Scan Probe is slid over the coated surface in Auto Repeat Mode, a coating thickness reading is taken approximately every half a second. Each individual dry film thickness reading is stored into the memory.

With a reading rate in excess of 140 readings per minute, the Auto Repeat Mode can significantly speed up the dry film thickness inspection of large coated areas.

• Counted Average Mode

 

Coating Thickness Gauge are supplied with the Counted Average Mode. Once the user has defined the number of individual gauge readings to be taken within a spot measurement, the coating thickness gauge stores the average of the individual gauge readings into the memory.

 

• Fixed Batch Sizes

 

The Fixed Batch Size feature within the Elcometer 456 Coating Thickness Gauge Model T allows users to define the maximum number of readings in each batch. Once the maximum number of readings has been reached the thickness gauge automatically opens up a new batch which is linked to the previous batch (name-1, name-2, etc.).

• Standards and Test Methods

 

 

International Standards and test methods often describe the number of individual coating thickness gauge readings to be taken in a spot measurement and/or the number of spot measurements required over a defined surface area.

SSPC PA2 requires a minimum of three coating thickness gauge readings to be taken per spot measurement and five spot measurements over 10m²(~100ft²).

The Elcometer Coating Thickness Gauge can be set with a counted average of three and a fixed batch size of five to meet these requirements. Each batch defines an area of measurement.

When the Ultra/Scan Probe is connected to the DFT Gauge with Auto Repeat Mode selected, SSPC PA2 (or similar test methods) can be completed more than 40% faster.

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.

This simple, pull-off gauge is a top-pocket, lightweight, foreman’s type gauge for spot check indications of coating thicknesses.

 

v Insensitive to hot and cold coatings or surfaces

v ideal for hot sprayed metal coatings for immediate results

v Easy to use and lightweight

v 3 scales on the instrument body: mils, microns and linear

v Pre-calibrated with no adjustment required

Ranges : Three scales printed on the body: 0 - 600µm
Linear (0 - 10 equally spaced divisions)

Accuracy : ±15% of the reading

The amount of force needed to remove a magnet from a Ferrous Substrate and are basic “Coating Thickness Gauge” to measure coatings on steel.

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.

This Coating Thickness Gauge commonly referred to as the "Banana Gauge," has proven to be a successful coating thickness gauge up to 6 mm
where the use of electronic instruments is difficult to measures non-magnetic coatings, including paint, hard chrome, electroplating, galvanising, powder coating, plastic, epoxy and rubber applied to a ferromagnetic base.

The banana gauge works on the principle of magnetic resistance, by means of a small magnet and a tensioned spring.
The amount of force needed to remove a magnet from a Ferrous Substrate and are basic “Coating Thickness Gauge” to measure coatings on steel. The "v" grooved base, rubber feet and clear scale with its ranges for thicker coatings, make this instrument one of the most popular mechanical gauges in the world.

This is one of the most popular mechanical gauges in the world.

• Factory calibrated - with user calibration adjustment

• Foils supplied to check calibration on site

• Ideal for cold surfaces and underwater use

• Small and portable with an accuracy ±5%

• The “V” grooved base, ideal for pipeline inspection

• Available in either Metric or Imperial versions, the Elcometer 211

measures coatings up to 6mm (250mils).

This Gauges does not required batteries to operate & It is Ideal for many critical area like underwater coatings inspection, Hazardous areas, Very cold surfaces, Inflammable atmospheres in oil and gas production

It is factory calibrated with user calibration adjustment & Also Calibration Foils supplied with Gauge to check calibration on site

A well-integrated service support is provided from service centre with team of factory trained customer support group headed by a Service Manager, who double up for technical & application support to our customers.

 Elcometer 211 Coating Thickness Gauge can be used in accordance with the following National and International Standards: AS 3894.3-A, AS 2331.1.3, AS/NZS 1580.108.1, ASTM B 499, ASTM G 12, ISO 2808-7A, supersedes BS 3900-C5-6A, BS 5411-11, DIN50981, ISO 2808-6A, ASTM G 12, ISO 2178 supersedes BS 5411-11, NF T30-124, SSPC-PA2.

Additional Information:

• Packaging Details: Elcometer 211, calibration foil set, carry pouch, neck harness and operating instructions

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.

This instrument is similar to the Elcometer 3230 Wet Film Wheel, but is designed for use in the coil coating process.

The outer wheels are knurled to allow measurements to be taken on slippery coatings or on fast moving substrates.

By rolling the gauge through a wet coating, the centre wheel eventually touches the film. This point on the scale indicates the thickness.

When the volume to solids ratio of the coating is known (generally found on the product data sheet supplied by the manufacturer), the wet film thickness can be used to predict the dry film thickness.

Additional Information:

• Packaging Details: Wet Film Wheel, storage case and operating instructions

Product Details:

The Elcometer 3233 Pfund Thickness Gauge is a simple but effective gauge which is used to determine the wet film thickness of paints and similar products The gauge is ideal for measurement of translucent products (varnish, oil, etc.)
The gauge consists of two concentric cylinders, one sliding inside the other. A spherical glass lens is fitted to the bottom of the inner cylinder.When the gauge is pressed down onto the surface being tested the lens becomes immersed in the wet film. The thicker the film, the greater the diameter of the paint spot left on the lens.
For ease of use, the gauge includes a stainless steel rule for measuring the diameter of the paint spot. A conversion table in these instructions allows the diameter to be converted into film thickness.

Additional Information:

• Packaging Details: Pfund Thickness Gauge, stainless steel rule, conversion table, storage case and operating instructions

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.This gauge is a simple but effective instrument used to determine the thickness of wet paints and similar coatings immediately after application. The expected dry film thickness can then be calculated.

Wet Film Combs:

• The edge of the comb is placed into the wet film and then removed. The thickness of the wet film is determined by examining the paint left on the teeth of the comb and the thickness scale marked on the front face of the comb.
• Precision formed in stainless steel to be long-lasting and reusable, these hexagonal wet film combs are supplied in a range of thicknesses up to a maximum of 3000 µm (120 mils). This high upper value allows measurement of thick coatings which are difficult to test by other methods. An aluminium version is available this model is not as accurate as the high precision versions but it does provide a low cost alternative for measurement of wet film thickness.

Range : 25-3000 micron

25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 1000, 1100, 1200, 1400, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000 µm

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.This gauge is a simple but effective instrument used to determine the thickness of wet paints and similar coatings immediately after application. The expected dry film thickness can then be calculated.


STANDARDS:
ASTM D 4414-A, AS/NZS 1580.107.3, BS 3900-C5-7B, ISO 2808-1A, ISO 2808-7B, JIS K 5600-1-7, NF T30-125, US NAVY PPI 63101-000, US NAVY NSI 009-32

Product Details:

Available in four scale ranges, the Elcometer 155 Uncured Powder Film Comb is designed to measure uncured powder coating film thickness.

This enables the application system to be set up and fine tuned prior to the curing process. In turn, this will reduce the amount of scrap and over-spray.

Place the comb into the powder and slide the comb along the surface. The measurement points (or teeth) are pointed and allow the powder to flow around them.

The thickness of the powder lies between the highest value where a drag mark is visible and the lowest value where a drag mark has not been produced.

Note: The thickness of a coating prior to cure is not the same value after curing but there is a correlation. The powder comb is suitable as a guide only.

Product Details:

We are engaged in providing the broad assortment of Coating Thickness Gauges.This gauge is a simple but effective instrument used to determine the thickness of wet paints and similar coatings immediately after application. The expected dry film thickness can then be calculated.

Wet Film Combs:

• The edge of the comb is placed into the wet film and then removed. The thickness of the wet film is determined by examining the paint left on the teeth of the comb and the thickness scale marked on the front face of the comb.
• Similar to the it provides the user with more measurement points (teeth). These rectangular wet film combs are available in 3 ranges up to a maximum thickness of 1200 µm (50 mils) - supplied either separately or in a set of 3.

Product Details:

The Elcometer 101 Coating Thickness Gauge is a mechanical coating thickness gauge for measuring nonferrous coatings or sheets applied to or laid on a ferrous magnetic base
The original non – destructive dry film thickness gauge, the Elcometer 101 Magnetic Coating Thickness Gauge was the world’s first portable coating thickness gauge with the original being produced in 1947.
Insensitive to hot and cold surfaces – ideal for hot sprayed metal coatingsIncorporates reading hold featureAccuracy of ±10%Ideal for hazardous areas
The Elcometer 101 Magnetic Coating Thickness Gauge can be used in accordance with:
AS 2331.1.3ASTM B 499ASTM G 12BS 5411-11ISO 2178SSPC PA2Standards not in bold have been superseded but are still recognised in some industries
Operation :Hold the Elcometer 101 Coating Thickness Gauge at right angles to the surface to be measured, place the two contacts on the surface and push down the small button to release the pointer.When the pointer comes to rest, it will indicate the thickness of the coating. Readings can be speeded up by using the push button as a brake by pumping it in and out until the pointer comes to rest.If the component has become magnetised take an average of two readings through 180° at the same point.
Calibration :
Take a foil equal in thickness to approximately mid scale reading and place this on an uncoated base ofsimilar material to that to be measured. With the large zero button adjust the scale to the thickness of thefoil. This is a more accurate method than setting the instrument to zero on an uncoated base.To obtain an accurate reading the meter should be read with the pointer in line with zero button. Formaximum accuracy keep the instrument clear of strong magnetic fields.

A well-integrated service support is provided from service centre with team of factory trained customer support group headed by a Service Manager, who double up for technical & application support to our customers.

Mechanical Coating Thickness Gauges are an ideal choice when coating thicknesses need to be measured where batteries cannot be used or are difficult to obtain. For example in remote locations, underwater, where dangerous gasses are present, you are looking for a basic coating thickness gauge to measure coatings on Ferrous Substrates (e.g. steel).These gauges all use the original method of measurement – the amount of force needed to remove a magnet from a Ferrous Substrate and are basic coating thickness gauges to measure coatings on steel

Product Details:

Elcometer 154 Plastic Wet Film CombsThe Elcometer 154 Wet Film Combs are made from ABS plastic and are designed to be used once and kept as a record of wet film thickness measurement for quality assurance or customer requirements.

Metric and Imperial values are on the same wet film comb, 50 to 800µm on one side, 2 to 32mils on the other.

Each comb has 16 measurement steps.

Dimensions : 40 x 40mm (1.57" x 1.57”)

Additional Information:

• Packaging Details: Elcometer 154 Wet Film Comb

Using third generation proven airborne ultrasonic technology, the Powder Thickness Gauge accurately predicts cured coating thickness by non-contact measurement of coating powders.

Other Details:

• Accurately predicts the cured coating thickness within ± 5% of the reading or ±5µm (±0.25mils)
• Ergonomic gun designed for comfort when taking multiple readings
• Hand held sensor allows easy positioning of the gun for fast measurement
• Large illuminated colour display with positioning graph to guide orientation of sensor probe
• Tough aluminium case, ideal for testing in an industrial environment

We are engaged in providing the broad assortment of "Thickness Measurement" products. The Elcometer 124 Dial Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex Replica Tape.

We are engaged in providing the wide range of Coating Inspection Instruments. Digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness measurements on almost any substrate, whether ferrous or non-ferrous. Dry Film Thickness can be measured on either magnetic steel surfaces or non-magnetic metal surfaces such as stainless steel or aluminium using a digital coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel. The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates.

We are engaged in providing the broad range of Paint meter/DFT Gauge. Elcometer 355 Coating Thickness GaugeThe Elcometer 355 Coating Thickness Gauge's watchwords are accuracy, simplicity, versatility and durability making this a true state of the art hand-held measuring system packed with time-saving and cost-cutting features. Available as a standard and top model, the unit’s large memory stores up to 10,000 readings in batches and data can be output to PC, datalogger or printer as required. With a comprehensive range of Probe Modules available, simply select the most appropriate for the application. All modules are supplied with calibration foils.

 

Other Details:

• ±1% or 1µm, whichever is the greater, accuracy
• Rugged aluminium case designed for the toughest environments
• ElcoMaster^® software supplied
• Full statistical analysis - mean standard deviation, number of readings, highest and lowest value
• RS232 output
• Date and time stamp
• Each coating thickness gauge is supplied without a probe allowing the choice of the correct probe for the relevant applications.

We are engaged in providing the wide range of DFT gauge Probe. coating thickness gauge probes are fully interchangeable and are available in a number of designs and scale ranges to meet your specific application.

Product Details:

Digital Glass thickness meter is mainly used on measuring glass and air space in insulated glass (IG), single glass, double glazing, or insulating glass. it also can measure individual panes of glass and the thickness of a glass bottle etc, special for those situations where common ruler cannot easily do it.

Feature:

• Laser reflects on CCD to measure glass thickness and Air thickness

• Measure Glass & Air Space (insulated glass) quickly from single side of IG Units

• Accuracy: +/- 0.2mm

• Large LCD, simple operation, easy reading result value

Product Details:

We are engaged in providing the wide range of coating Inspection Instruments. We provides a range of Zero Test Plates to ensure correct calibration of the coating thickness gauge.When used in conjunction with a set of foils, Zero Test Plates are ideal to test a coating thickness gauge’s functionality and calibration, ideal for when it may be difficult or impractical to obtain an uncoated substrate.

We are engaged in providing the wide range of Coating Inspection Instruments. The Eloometer 311 Paint Meter / Automotive Refinishing Gauge has been specifically designed to meet the requirements of today's automotive market. The Elcometer 311 is available in two options. The ferrous only instrument is ideal for measuring steel car body panels. The Dual FNF instrument enables the user to take measurements on both steel and aluminium car body panels using one gauge. Pre-calibrated on steel and aluminium car body panels, the Eloometer 311 is very easy-to-use. Check pieoes are supplied with each instrument to verify its performance.
Features:

• Designed specifically to meet the requirements of the automotive industry.
• Ferrous Only and Dual FNF gauges available
• Pre-calibrated on automotive steel and aluminium.
• Bigfoot“ for stable, repeatable readings.
• Scale range of 0-5 ooum (0- 2 omils)
• Auto on/off switch
• Check piece included to verify
• performance - FNF gauge
• comes complete with ferrous
• and non-ferrous check pieces.
• Available in Metric or Imperial
• Units

Ultrasonic Thickness Gauge Transducerslcometer has a wide range of transducers available for use with the Elcometer 205, 206 & 208 range of Ultrasonic Thickness Gauges. When selecting a transducer, it is important to choose one which will meet the application, taking the following into consideration.

Other Details:

• The type of material to be tested
• The design of the transducer probe
• The measurement range
• Whether the shape of the substrate is flat or curved or hard to reach
• A range of frequencies and sizes are available to meet specific needs
• Straight and right angle transducers available as potted or microdot

Speed of Sound Through Materials

• Elcometer Ultrasonic Thickness Gauges can be calibrated by the user for the appropriate material in two ways:
• Set the calibration to the thickness of the known standard of the same material
• Set the frequency calibration to the appropriate value using the velocity chart below:

 

Product Details:

Product Details:

We are engaged in providing the wide range of DFt gauges accessories. All coating thickness gauge calibration foils are ideal for use in the laboratory, on the production line or on site. Calibration foils or shims are the most convenient way of creating a coating thickness standard on the substrate material, surface finish or form. Shims provide the ideal method for adjusting the calibration of the coating thickness gauge to ensure the greatest possible accuracy.

Features:

• Metric and Imperial values displayed on each calibration foil
• Available individually or in shim sets
• Precision foils with ±1% accuracy
• Each shim has a unique serial number for traceability
• Shims are available in thicknesses from 12.5μm to 20mm (0.5 to 790mils)

Calibration Foil Sets   (Value in Micron)
Scale 1 : 25, 50, 125, 250, 500, 1,000Scale 2 : 25, 50, 125, 250, 500, 1,000, 2,000, 3,000 Scale 3 : 250, 500, 1,000, 2,000, 4,000, 8,000 Scale 4 : 12.5, 25, 50, 125, 250Scale 5 : 12.5, 25, 50, 125, 250, 500Scale 6 : 1,000, 2,000, 5,000, 9,500, 15mm, 25mmScale M3 : 12.5, 25, 50, 125, 250, 500Scale 2B2 : 25, 50, 125, 250, 500, 1,000, 2,000, 2,000

Product Details:

We are engaged in providing the broad assortment of Paint Inspection Gauge ( P.I.G.) designed to measure the thickness of single or multiple layers of coatings. Combinations of coating and substrate it is necessary to use a destructive measurement method. specific design to measure the thickness of single or multiple layers of coatings.

Additional Information:

• Packaging Details: Elcometer 121/4, cutters 1, 4 and 6, x50 microscope, 4 x AG3 batteries for lamp (fitted), hexagonal wrench, black marker pen, wrist strap, carry case and operating instructions

Product Details:

PIG is a quick, versatile method of examination and destructive measurement of coatings in a portable, easy to use instrument. Ergonomically designed to give a balanced weight distribution for a consistent cut. it is ideal for tough coatings and enamels.

Additional Information:

• Packaging Details: Elcometer 141 P.I.G, x50 microscope, 3 cutters, marker pen, hexagonal wrench, carry case and operating instructions

Product Details:

The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex^® Replica Tape.

• Available in both Metric and Imperial versions
• Quick and easy to use
• Anvil pressure as required in the Standards.

 

Testex Replica Tape is designed to provide a permanent mould of the surface profile, which can then be measured using a thickness gauge. Testex Tape consists of foam with a non-compressible backing. The foam side is rubbed into the surface providing a permanent mould of the peak-to-valley profile. The profile of the surface can then be measured using the Thickness Gauge. Testex Replica Tape is available in four profile ranges. It is important that the tape grade chosen is reflective of the profile being measured.

Product Details:

Calibration foils or shims are the most convenient way of creating a coating thickness standard on the substrate material, surface finish or form. Shims provide the ideal method for adjusting the calibration of the coating thickness gauge to ensure the greatest possible accuracy.

Other Details:

We are engaged in providing the wide range of Coating Inspection Eqipments. Formal quality systems, such as those described in ISO 9000, require gauges to be properly controlled, logged and in calibration. Increasingly, users are specifying that the readings taken by gauges are traceable to National Standards. There are three types of coating thickness standards available : calibration foils, coated standards and zero test plates. Coated Thickness Standards are hard wearing, durable and are mounted in a protective folder. The calibration standards provide the user with an ideal method to accurately measure the performance of the coating thickness gauge.

Features:

• ±2% accuracy, supplied with Calibration Certificate as standard
• Available with either Ferrous (F) or Non-Ferrous (N) substrates
• Each calibration standard is individually serial numbered for traceability
• Can be re-certified by Elcometer to meet ISO requirements
• Calibration standards available in a range of thicknesses
• Special thicknesses can be supplied to meet specific needs
• Coated with a hard wearing film for extended life span

Other Details: